Why Learning Plumbing Basics is Essential for Bathtub Installation
Why Learning Plumbing Basics is Essential for Bathtub Installation
Blog Article
On this page in the next paragraph you might get lots of superb information regarding A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging job. If the old tub is easily available, the project can relocate easily; if you have to open up a wall to get rid of the old tub and also position the new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. As opposed to hiring a specialist to take over a halfway-completed project, it is better to think about employing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This post will certainly help you install a new tub in your shower room if you have already bought a brand-new tub and also do not need to change the setup of your previous water pipelines.
Your tools and product list ought to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the restricted access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipes. Once the supply pipelines have been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Before carrying on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in area between the tap and the sink. Protect the faucet in position with the maker given backnut. As soon as the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former kind must be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Using the two wood boards under its feet, place the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the tub till the level reads degree.
To install faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water supply and inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill up the bathtub and also check the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the manufacturer's user's manual. Tiling and sealing around the tub needs to wait up until the bath tub has been made use of a minimum of when as this will settle it right into its final position.
Getting ready for the Installment
First of all, the sustaining framework provided with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to avoid strain on the bathtub.
Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a rigid seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, resulting in problems with wetness and possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to always load the tub with water prior to sealing, to allow for the movement experienced when the bathtub is in use. The sealer can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that article on A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different website. Are you aware of someone else who is looking into Tools You Need to Install a New Bathtub ? Be sure share it. Thanks for your time. Kindly check up our site back soon.
Professional-grade solutions. Report this page